modellbahn·fokusThe digital reference archive of model railways · A project by Modellbahnshop Lippe
EN
Home› Manufacturers› ESU› 54685
ESU54685

LokPilot micro V4.0, DCC, 6-pin

LokPilot micro V4.0, DCC, 6-pin. NEM 651 direct connection

No longer in the shop

Description

LokPilot micro V4.0, DCC, 6-pin. NEM 651 direct connection

The LokPilot micro V4.0 DCC can drive the locomotive motor with an output power of up to 0.75A and, in contrast to its predecessors, has shrunk significantly: The smallest member of the LokPilot V4.0 family is only 10.5 mm x 8.1mm x 2 , 8mm small.

modes
The LokPilot micro V4.0 DCC uses the DCC protocol. It can be operated with 14, 28 or 128 speed steps or can be used on analog DC systems. You can either use two-digit or three-digit (1-127) or four-digit (1-9999) addresses or assign a traction address (consist address). All common DCC brake systems such as Lenz LG100, but also the new Lenz ABC brake modules with asymmetrical DCC signal are taken to heart, as is braking in the DC section with reverse polarity (Brake on DC). The decoder masters the calculation of a constant braking distance so that your locomotives stop correctly in front of the red signal regardless of the speed. The decoder can switch between operating modes fully automatically during operation.

motor control
The LokPilot micro V4.0 DCC is equipped with load control of the improved 5th generation. The control frequency can be adapted adaptively to the speed at a base frequency of 40 kHz and ensures an even better, silky smooth, absolutely quiet engine running for many engines. The 10 bit A / D converter lets your locomotives crawl super slowly on the layout. With Dynamic Drive Control (DDC) you limit the influence of the load control and can regulate sensitively in the station and switch area, while on the (fast) route the locomotive slows down prototypically when driving uphill. The load control copes perfectly with all common motors, regardless of whether from ROCO®, Fleischmann®, Brawa®, Bemo®, Faulhaber® or Maxon®. 0.75A continuous current are more than sufficient for the above-mentioned motors and offer sufficient power reserves even for long block trains.

analog operation
The LokPilot micro 4.0 DCC decoder can also be used on analog DC trains.

features
The LokPilot micro V4.0 decoder DCC has two function outputs, each with 150mA continuous current, which can be individually assigned a function. Two additional unamplified outputs can also be used to control special functions using an external transistor. All important lighting functions such as flashing lights, strobes, alternating indicators, firebox simulation, etc. are available. The brightness of each output can be set separately. The decoder masters automatic coupling and uncoupling when uncoupling couplings and now also offers a high beam function. The "LED mode" ensures correct lighting effects when using LEDs.

operational safety
If required, you can connect a Powerpack to the LokPilot micro V4.0 DCC (ESU 54670, see page 62). This energy store supplies the decoder with energy when the power consumption is not optimal due to dirty rails.

RailComPlus®
With RailComPlus®, the decoder now registers fully automatically at suitable control centers and receives a new address if required. Forget the tedious typing and programming!

Future built in
LokPilot decoders are capable of firmware updates. You only need the ESU LokProgrammer.

Specifications

Digital-DecoderDCC
DCC addresses1-9999
DCC-Fahrstufen14, 28 oder 128
Funktionsausgänge2
Belastung Funktionsausgang150 mA
Motor connector750 mA
Short circuit protectionYes
Dimensions (LxWxH)10,5 x 8,1 x 2,8 mm

Reference data

Manufacturer’s item no.54685
EAN4044645546857
ScaleN (1:160)
Era–
Power system–
Railway company–

Market value

Coming soon

The modellbahn·fokus market value index will in future show reference values for both available and discontinued models — transparently derived and continuously updated.

Comments from members (0)

No comments on this model yet – be the first.

Only signed-in members can write comments. Sign in now

Report an error or suggest an addition

Do you know this model better? The editors review every note.

Please sign in to suggest a correction or an addition.