Description
3 amp DCC booster without power supply
The DR5033 is a DCC H-bridge booster with a maximum output current of 3 amps. The booster is equipped with various connection options. This makes it possible to operate the booster with a variety of control panels. The booster can automatically change the polarity (phase change) of the output if a connection error is detected on the track, which otherwise would have led to a short circuit. The booster can be connected to all common bus systems. The DR5033 has a CDE connector (Lenz ™), B-Bus ™ (Roco ™), L.NET-T (Intellibox ™) and a Railsniffer input that allows you to pick any track signal and then pass it on 1: 1 (PIKO ™ Digi1, EcOS ™, etc.).
The booster can be extremely flexibly configured by L.NET LNCV programming to adapt it to your needs. When connected to the L.NET, the DR5033 can be switched on and off either via the STOP-GO buttons of the control panel or via a configurable solenoid address. The booster reports its status via L.NET to the control center. The load (0-100%) and the temperature of the H-bridge in degrees C can be read out via LNCV. When connected to the L.NET, a configurable solenoid address can be used to reverse the polarity of the booster. In addition, the booster with 2x2 adjustable Rückmedeadressen can be monitored (2x reverse polarity, 2x reverse polarity off), so it is possible to create a short circuit-free reverse loop.
Roco Z21 / z21 / MultiMouse
R-BUS
L.NET
Lenz DCC CDE
TRACK SNIFFER
H-BRIDGE
Railcom
18V / 3 amp
Automatic polarity reversal phase detection / correction
The DR5033 is a DCC H-bridge booster with a maximum output current of 3 amps. The booster is equipped with various connection options. This makes it possible to operate the booster with a variety of control panels. The booster can automatically change the polarity (phase change) of the output if a connection error is detected on the track, which otherwise would have led to a short circuit. The booster can be connected to all common bus systems. The DR5033 has a CDE connector (Lenz ™), B-Bus ™ (Roco ™), L.NET-T (Intellibox ™) and a Railsniffer input that allows you to pick any track signal and then pass it on 1: 1 (PIKO ™ Digi1, EcOS ™, etc.).
The booster can be extremely flexibly configured by L.NET LNCV programming to adapt it to your needs. When connected to the L.NET, the DR5033 can be switched on and off either via the STOP-GO buttons of the control panel or via a configurable solenoid address. The booster reports its status via L.NET to the control center. The load (0-100%) and the temperature of the H-bridge in degrees C can be read out via LNCV. When connected to the L.NET, a configurable solenoid address can be used to reverse the polarity of the booster. In addition, the booster with 2x2 adjustable Rückmedeadressen can be monitored (2x reverse polarity, 2x reverse polarity off), so it is possible to create a short circuit-free reverse loop.
Roco Z21 / z21 / MultiMouse
R-BUS
L.NET
Lenz DCC CDE
TRACK SNIFFER
H-BRIDGE
Railcom
18V / 3 amp
Automatic polarity reversal phase detection / correction
Specifications
Data formatsDCC / Motorola
Reference data
Manufacturer’s item no.DR5033
EAN–
ScaleNeutral
Era–
Power system–
Railway company–
Market value
Coming soon
The modellbahn·fokus market value index will in future show reference values for both available and discontinued models — transparently derived and continuously updated.
Comments from members (0)
No comments on this model yet – be the first.
Only signed-in members can write comments. Sign in now
Report an error or suggest an addition
Do you know this model better? The editors review every note.
Please sign in to suggest a correction or an addition.



